make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled

　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, it should continue to be used after maintenance. Do not dump it directly　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the probability of pump sticking will be much smaller!Vienna,　　Clean up the silt and other obstructions in or around the water pump.　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.Vinh Long,ViennaUsed pipeline pump,　　 The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.　　 Then reinstall the equipment on the engine and install the rubber hose.　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.

　　At present, mechanical seals occupy an increasing share in the slurry pump seal market.　　 When the slurry pump operates, it rotates at a high speed, and the components of the slurry pump have a heavy weight. Therefore, once it reverses, the force will directly push the impeller to the outside, and the impeller collides with the sheath and guard plate. If the speed is high, the force ratio is low　　Different installation requirements: the vertical slurry pump needs to be fixed while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.discount,　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor　　The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure,ViennaHorizontal slurry pump,ViennaDrilling fluid slurry pump, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submerged

　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.demand,　　Stop, then tighten the bearing seat, press down the nut and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose　　 There are many reasons for motor overheating. It may be because the power supply voltage is too high, or there is a problem with the water pump or the motor itself.　　Moreover, the leaked flammable, explosive and toxic liquid will cause fire, explosion and poisoning,　　When the submersible slurry pump is used at ordinary times, cavitation usually occurs, which has a great impact on the impeller of the equipment itself. So how to detect whether there is cavitation when using the equipment at ordinary times?　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.　　Only in this way can its service life be extended to a large extent.