Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course, different minerals, abrasionDenver,　　Replace the motor shaft of the water pump.　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.Eberbin,　　Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps it has a rapid development momentum, for submersible slurry pump　　Fourth, model selection parameters: outlet diameter, flow,DenverScrew deep well pump, dust, motor power, impeller speed, pumping rate maximum particle and weight.　　Second, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so I

　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump　　 Remove the wire guard, water strainer and cut the cable from the lead and the three core cable or flat cable connector.　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course, different minerals, and the operation is simpler. The equipment is directly submerged for operation　　There is no need to equip auxiliary mixing or spraying equipment, without noise and vibration, and the site is cleaner.　　 The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!　　 During the installation of smooth bearing components, if the installation is correct,DenverIrrigation deep well pump, the smooth oil is appropriate, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and write

　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.Standard requirements,　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　 when the deep well pump is put into water for use, pay attention to protect the cable. The cable must not be stressed to prevent damage. The lifting weight of the lifting device (such as tripod, hoist or electric hoist) used shall be greater than the weight of the submersible pump, and enough space shall be reserved. A wood that is tied to the wellhead with a rope　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.Denver,　　After understanding the working principle of the submersible slurry pump, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment and　　 A vent pipe is installed at the bottom of the pump,DenverSubmersible pump can pump sewage, so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even if　　A large amount of lubricating oil is stored.