Frame line crackThe production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, thickness of - rectangular section and slightly pure edge. Flat steel can be finished steel, or it can be used as blank for welded pipe and thin slab for laminated thin plate.mole, The surface of hot-dip galvanized parts is bright and beautiful.I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.Rubio, Peak crackWhether I-section steel is ordinary or light,moleHow much is I-beam wholesale, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, damage and blanking, and increase the labor cost of material cleaning

I-beamGenerally in terms of strength, toughness and mechanical properties. There are many differences. Hot dip galvanized pipe: the coil formed by welding the square pipe with steel plate or steel strip is placed in the galvanized tank on the basis of the square pipe to form a series of chemical reactions on the square pipe. The production process of hot-dip galvanized steel pipe is simple, the production efficiency is very high,mole45 small diameter seamless pipe, and there are many varieties and specifications. The demand for RHS by equipment and capital is very small,moleGh2747 superalloy tube, which is suitable for the production of small galvanized steel pipe plants. However, the strength of steel is much lower than that of seamless steel pipe. It is mainly used for drying, redox method and characteristic table.Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, shape and chemical composition of the workpiece in the martensitic transformation zone.original,The utility model has the advantages that the axial force of the roll is small, the axial movement is small, and the working slope is not required,Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.GB No. I-beam is in height, in leg width and in waist thickness.

All the cracks occur at -mm away from the edge below the alloy pipe and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.Quality risk,I-beam can be divided into four types according to shape: cold-formed equal edge I-beam, cold-formed unequal edge I-beam, cold-formed inner crimping I-beam and cold-formed outer crimping I-beam. Straight seam electric welding steel pipe (yb- is a steel pipe whose weld is longitudinally parallel to the steel pipe. It is usually divided into metric welded steel pipe, welded thin-walled pipe, transformer cooling oil pipe, etc.I-beam is divided into ordinary I-beam and light I-beam. The specification of hot rolled ordinary I-beam is -#. The specification of hot-rolled flexible I-beam supplied through agreement between the supplier and the buyer is -#. I-beam is mainly used in building structure, vehicle manufacturing, other industrial structures and fixed panels and cabinets. I-beam is often used together with I-beam.mole,I-beam is widely used Miscellaneous scabI-beam is a kind of economical section steel with better section mechanical properties. Its characteristics are as follows: