The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition,Special shaped pipe: square pipe, rectangular pipe, cap pipe, steel pipe for hollow rubber steel doors and windows welded by general carbon structure steel and Mn steel strip, mainly used as agricultural machinery components, steel windows and doors, etc.I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam,SarovaHow many kilograms per meter of 100mm welded pipe, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.Appeldoren,According to the theory of steel structure, that is, the I-beam should be standing rather than lying down. Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded.Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, the axial movement is small, the working inclined plane is not required, the pass occupies a small length of the roll body and more passes can be matched under the condition of a certain length of the roll body.Galvanized pipe is a kind of light thin-walled steel pipe with hollow square section, which is made of Q hot-rolled or cold-rolled strip or coil as the base material also known as steel cold-formed profile. It is a section steel with square section shape and size, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot rolled extra thick wall galvanized pipe reach or even exceed the level of resistance welding cold formed galvanized pipe.Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.Bidding,When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.Last week, the billet in North China market showed a slight rebound trend. The billet quotation in Tangshan the leading city, rose first and then stabilized in four trading days, with a strong wait-and-see atmosphere in the market. Affected by the almost stagnation of festival procurement,SarovaHow much is 114 seamless pipe per ton, Tangshan billet fell by yuan during the Dragon Boat Festival holiday. On the first day after the festival, although the phase snail is still running at a low level, due to the small billet resources in the market, the steel mills unexpectedly rose, and the billet market rebounded. However, due to the continuous increase of capital pressure and the downturn in the transaction of downstream finished materials, the steel plant has always maintained a cautious wait-and-see attitude to maintain stability.I-beam, also known as universal beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.

Alloy tube is widely used in our daily life, which provides us with great assistance. So what industries are alloy tubes applied to? Let&#;s follow the steps of all manufacturers and have a look together:Fair price,The alloy tube can be hardened by induction heating, so it has excellent rolling fatigue characteristics and corrosion resistance. Therefore, this kind of steel has been widely used as the material of rolling mill flap ball screw in rolling mill manufacturers. In addition to the excellent properties of cronidur steel, and its application range is expected to be further expanded.Thanks to a zinc tube, stand in the formation and development of painful microorganisms.Precision cold rolling of small and medium-sized bearing sleeves with alloy tubes can greatly improve material utilization, bearing performance and service life. This paper systematically introduces the development of high quality cold drawn bearing steel pipe and its application in bearing. Precision cold rolling of small and medium-sized bearing sleeves with bearing steel pipes can greatly improve material utilization, bearing performance and service life. This paper systematically introduces the service life of high quality cold drawn bearings.Sarova,H-section steelHeating surface pipes, economizers, superheaters, reheaters pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)Key technical characteristics of alloy pipe