It is widely used in various fields of national economic construction, such as buildings, bridges, power stations, oil drilling platforms vehicles, highways, steel structure plants and large warehousesGB No. I-beam is in height, in leg width and in waist thickness.Koniki,According to the data information display information, there is an inseparable correlation between the annual real estate sales data information and the apparent consumption data information of galvanized pipe. From the consumption surface of the middle and lower reaches of galvanized pipe, decoration design, elevator car, handicrafts, household appliances and other industries are closely related to the situation of the real estate industry.C - section steel is reliable and stable in stress, can be accurately positioned, and is resistant to impact and vibration Moreover, it has good versatility and combination, and has a variety of C-section steel and size selection to ensure its flexibilityButajira,Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption,KonikiWill reinforced concrete rise or fall in 2021, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.I-beam

I-beam can be divided into four types according to shape: cold-formed equal edge I-beam, cold-formed unequal edge I-beam, cold-formed inner crimping I-beam and cold-formed outer crimping I-beam.A major defect is its instability to the corrosion process which can not resist all factors. Producers need a solution that can solve the corrosion problem. The decision has been found. They become a galvanized steel pipe.The specification of pass design I-beam is expressed in cm of waist width. For example, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Discount, when the circular cross section bears the internal or external axial working pressure a large amount of liquid can be transported with an annular tube. In addition, the bearing force is more symmetrical. Therefore, most seamless steel pipes are round steel pipes.c. quality inspection is carried out for alloy pipes,KonikiHow much is 20cm I-beam per meter, so that the whole process of steel pipe processing is under reasonable inspection and supervision, and the product quality is reasonably guaranteed.After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.

Frame line crackHow much is it,Alloy pipes are widely used in building materials, and the test standards of alloy pipes are also different. Alloy pipe has high hardness and can be used at many levels, most of which is prestressed reinforcement. Where plastic deformation is not specified but compressive strength is specified,KonikiReinforcement proofing Engineer, such stainless steel plate can be applied.Check whether the manufacturer&#;s qualification, business license, organization code certificate, tax registration certificate, production and operation license and other qualification materials are complete. Look at the case, investigate the supplier&#;s performance and the projects served in the past. Whether there is a self built logistics fleet or not, and more importantly, ensure the timeliness of delivery. After sales service, whether there is a sound and reliable after-sales service guarantee system, and timely solve quality problems in arrival acceptance and subsequent use. Check whether the quality assurance materials such as product quality certificate, material specification and warranty are complete. Check the appearance of the welded pipe, the surface is smooth and flat, without burr, oil stain, corrosion, extrusion deformation and flat cross section. Use a micrometer to check whether the outer diameter and wall thickness of the welded pipe meet the requirements, and the standard wall thickness deviation shall not exceed % - %. NDT shall be carried out for welded pipe with flaw detector. Conduct bending tensile strength test according to the requirements, bend the welded pipe for degrees, and there is no crack at the bend.Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main sleeves of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Koniki,The shape of I-beam is similar to that of H-beam. What is the difference between them?I-beam can be divided into four types according to shape: cold-formed equal edge I-beam, cold-formed unequal edge I-beam, cold-formed inner crimping I-beam and cold-formed outer crimping I-beam.I-beam features: the content of chromium carbon alloy is -%, the hardness of chromium carbide alloy is V, and the macro hardness is - HRC