HaradokHow many kilograms of steel bar per meter, and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -, - and - according to different specification numbers. The length selection range of imported I-beam is generally -.The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Haradok, When the end span plate is connected with the concrete beam for structural reinforcement, the length of the surface mesh reinforcement extending into the beam shall not be less than d. When the beam width is small, the extended reinforcement shall be bent . When the perimeter of the floor is poured integrally with the concrete beam or wall the length of the surface mesh reinforcement extending into the beam shall not be less than the anchorage length of the small reinforcement required by the standard (without transverse reinforcement), when the beam width is small, the extended reinforcement shall be bent.Patented manufacturing process of I-beam: I-beam has become a new industrial standard for wear-resistant materialsMansura,Classification introductionPatented manufacturing process of I-beam: I-beam has become a new industrial standard for wear-resistant materials→ compared with general section steel, it has the advantages of low cost, and saves about % of the manufacturing cost of steel structure.

Dry processing technology: after passivation treatment, parts shall be dried with air compression or hot gas, or drying treatment or air drying can be selected.Seamless pipe production processWhen selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.Home page recommendation,The pickling agent in the pickling process contains many acidic substances, including hydrochloric acid sodium cyanide, etc., which has strong corrosion and reduction, and the temperature of etching substances is relatively high. Therefore, the corrosion resistance of alloy pipes is specified higher.I-beam, also known as universal beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.Alloy pipes can be used for heating (cooling) projects.

Defects of alloy pipe and solutions:Honest service,Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main sleeves of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.The two ends of the steel produced by the seamless pipe manufacturer shall be cut into right angles, and the burrs on the surface shall be removed, which is the raw material used by the seamless pipe manufacturer. The embryo prototube embryo needs to be cut by a cutting machine to form an embryo material with a length of about one meter, which is sent to the furnace for heating through the conveyor belt. The billet is sent to the furnace. After internal heating, the temperature is about degrees, and the fuel used is often ethyne. Temperature control in the furnace is a very key factor.→ wide flange and large lateral stiffness. Strong bending resistance.Haradok,Alloy pipe is a kind of seamless steel pipe. Alloy pipe is divided into structural seamless pipe and high-pressure heat-resistant alloy pipe. It is mainly different from the production standard and industry of alloy pipe. Annealing and tempering of alloy pipe changes its mechanical properties. Meet the required processing conditions. Its performance is higher than that of ordinary seamless steel pipe, its utilization value is higher,HaradokWhich reinforcement manufacturer is 441, the chemical composition of alloy pipe contains more Cr, and its performance of high temperature resistance, low temperature resistance and corrosion resistance. Ordinary carbon seamless tubes do not contain alloy components or have few alloy components. Alloy tubes are widely used in petroleum, chemical industry,HaradokSeamless pipe supplier, electric power boiler and other industries because the mechanical properties of alloy tubes change and are easy to adjust. Peak crackThe working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.