I-beam: national standard * what is the wall thickness of I-beamWhen selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.Slotsk,Characteristics and application of galvanized pipeThe flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.Epe,Mixed Scabs are distributed periodically, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal.In order to make the welded pipe have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming process, heat treatment process is often necessary. In addition, the mechanical, physical and chemical properties of aluminum, copper, magnesium,SlotskAlloy pipe 12Cr1MoVG, titanium and their alloys can be changed by heat treatment to obtain different service properties.When selecting I-beam in structural design, chemical properties, weldability and structural size. I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide medium and narrow flange I-beams.

What should we pay attention to in the production of alloy pipeGalvanized pipe is a name for square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment. Steel pipe has been an essential material in building decoration. Galvanized pipe is also used more in decoration, but hot-dip galvanized steel pipe manufacturers need to know about the size of galvanized pipe and several common sizes of galvanized pipe,The side length of I-beam is small and the height is large and the waist is parallel to the roll axis.Home page recommendation, so it can only bear the force in one direction.Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal,SlotskHow much is a meter of DN32 galvanized pipe, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Application characteristics of I-beam

The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, I-beam can also adopt special rolling method.Economic management,What is the purpose of flat steelIn hardware, you can choose an incomplete performance outside the product. Some construction experts claim that if there is a mechanical effect on these products, they are not suitable. At least this product is impossible.→ compared with general section steel, it has the advantages of low cost, high precision and small residual stress. It does not need expensive welding materials and weld detection, and saves about % of the manufacturing cost of steel structure.Slotsk,→ the two surfaces of the flange are parallel to each other, making it easy to connect process and install.Welded steel pipes need to be processed through various processes before application. The heat treatment of welded steel pipes is a very important link in the processing of welded steel pipes. Hot working is a metal hot working process in which metal materials are heated, and their metal properties are controlled by changing the metallographic structure on the surface or inside of the material. During the heating and cooling process of structural welded steel pipe workpiece insulated and cooled in a certain medium,SlotskHow much is 30 I-beam per meter, the temperature difference will be formed, which will lead to uneven volume expansion and contraction and produce stress, that is, thermal stress.The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.