The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts, but also reduce the service life of the parts.　　Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.los mochis ,　　And has a wide range of applications.　　With the continuous development of slurry pump technology,los mochis Pipeline pump, and of course it can be more than. For example, but such underwater depth is not the best operating depth of this kind of pump,los mochis Split vertical pipeline pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.Showot,　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating, so that the product can operate safely for a long time under adverse working conditions.　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular some equipment is frequently used at ordinary times, but the maintenance work is not done well when it is used, so it will be blocked after being used for a period of time　　All kinds of newly designed mechanical seals of submersible slurry pumps contribute greatly to the growth of market share.

　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline and After that, cut off the power supply of the motor. If the temperature of the environment is low, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　 the full-automatic control cabinet can be equipped according to the needs of users to automatically protect the water leakage, electric leakage, overload and over temperature of the pump, which improves the safety and reliability of the product.　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.How much does it cost?,　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve　　 The slurry pump mainly aims at conveying flow,los mochis Small deep well pump, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certain　　The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothing

　　There will be no insufficient liquid supply or other problems.Encyclopedic knowledge,　　Water flow into the bearing damages the bearing.　　 Check the winding of the motor: if the winding is damp or there are dust, sand and other attachments on the winding, which may reduce the insulation of the winding, it should be removed immediately.　　What should be paid attention to in the process? Let&#;s learn about the precautions for using the submersible slurry pump. When the equipment is in use, the pump itself generally needs to be placed on land for use, but its suction pipe needs to be placed in waterlos mochis ,　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the cut impeller is usually used. The cut is　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.　　Whether it is the pre installation inspection or the post installation commissioning inspection, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.