Ordinary vertical motor can be used without waterproof,Miguel Hidalgo Long shaft submerged slurry pump, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product and the submersible slurry pump is a newly developed product according to the market demand　　About %), and motor power p=i × U indicates that high power and current will increase.Miguel Hidalgo ,　　In recent years, domestic stainless steel pipeline pump products have greatly improved their technical level through introduction, absorption, renovation, digestion and innovation, especially the supporting products of some major technical equipment have reached or approached the advanced level of similar products.　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.Deinze,Miguel Hidalgo Baigang deep well pump,　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.

　　 If it is found that the impeller is damaged and the liquid supply is insufficient,Miguel Hidalgo Carbon steel explosion-proof pipeline pump, it is necessary to replace the new impeller in time for use.　　Is there an important cf fire control cabinet? Analyze the importance of configuring cf fire control cabinet for everyone.　　 If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current.Excellent service,　　The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.　　The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, corrosion-resistant, and can effectively pass through large solid particles. It is not limited by suction range with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothing　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.

　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flowsinstall,　　 Structural features and working principle qsz submersible slurry pump is a coaxial integration of water pump and motor. During operation the motor shaft drives the water pump impeller to rotate, and transmits energy to the slurry medium to generate a certain flow rate, drive the solid flow, optional flow range: - (m/h), lift range: - (m), caliber range: - (mm).　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.Miguel Hidalgo ,　　Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness, which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possible　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, so the water ring vacuum pump is used for exhaust to achieve the of water inlet.