St. JohnSteel pipe,

d. All machines and equipment in a production line can connect with the software of the computer data collection system to complete the timely transmission of data information, and the performance parameters in the production process are monitored by the central control room.Classification introductionSt. John,Spiral welded pipe: it is made by rolling low-carbon structural steel or low-alloy structural steel strip into pipe blank according to the viewpoint of certain spiral line (called forming angle), and then welding the pipe seam. It can produce large-diameter steel pipe with narrow strip steel. Spiral welded pipe is mainly used for oil and natural gas transportation pipeline, and its standard is expressed by outer diameter * wall thickness. Spiral welded pipe has single-sided welding and double-sided welding. The welded pipe shall ensure that the hydrostatic test, tensile strength and cold bending of the weld meet the requirements.The utility model has the advantages that the axial force of the roll is small, the axial movement is small, and the working slope is not required,Shchuchinsk Peak crackFunction of I-beam: where is I-beam mainly used?Nitriding: also known as nitriding, it is the process of penetrating nitrogen atoms into the surface layer of steel. At present, gas nitriding is widely used in the production of alloy steel pipe.

The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy,St. JohnQ235B welded pipe manufacturer, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust. When the mesh reinforcement on both sides of the beam is different,St. John12Cr1MoVG high pressure alloy pipe, and the reinforcement anchorage length is required.In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.Development Curriculum,When it is used for ground heating and hot spring transportation, cold and corrosion prevention. In addition mining and other industries to meet the provisions of cold, the chemical raw material transmission pipeline has a wide indoor space. Miscellaneous scab Hot stamping. Fix the plan product workpiece or preformed vacancy on the rotating journal, with the wheel working pressure vacancy, radial wheel. After one or several solutions, mold shell and software requirements specification scope, which are very simple, very easy to be replaced, and relatively low product cost. The processing time is not long enough, the processing capacity is not high, the total length of processing pipeline is limited, and the size of machinery and equipment is generally short.

I-beam is mainly used in building structure, curtain wall engineering, mechanical equipment and vehicle manufacturing.Quality assurance,Plan scheme : high carbon steel with carbon content exceeding .% and alloy pipe with chromium content not less than %The production methods of seamless pipe are roughly divided into cross rolling method and extrusion method. The cross rolling method is to drill the tube with a cross roll, and then extend it to the rolling mill. This method has fast production speed, but has high requirements for the workability of the blank. It is mainly suitable for the production of carbon steel and low alloy steel pipes. The extrusion law is to pierce the blank or ingot with a punch, and then squeeze it with a steel pipe with an extruder. The efficiency of this method is lower than that of cross rolling method. It is suitable for producing high-strength alloy steel pipe. The billet or ingot must be heated before cross rolling method and extrusion method. The produced steel pipe is called thermal correlation. Steel pipes produced by hot working can sometimes be cold worked as needed. There are two methods of cold working. One is cold drawing. In other words, pull the pipe to the pipe and tilt it to make the steel pipe gradually thinner and longer. Another method is cold rolling. The method of applying the hot smoke invented by brother to cold processing. The cold working of seamless pipe can improve the dimensional accuracy and finishing of steel pipe, and improve the mechanical properties of materials.Pass designSt. John,Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment, and the reproducibility of the solution is good.