important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, the motor temperature will rise, so it is easy to burn out the motor.Chihuahua City ,　　In the eyes of many people, cabinet making is superfluous. It doesn&#;t seem to matter whether there is one, but now it is not. The fire control cabinet is not optional, let&#;s have a look. Why fire department　　Screw it down, and then remove the bearing inner race, shaft sleeve and retaining sleeve in turn.Oupeye,　　There will be no insufficient liquid supply or other problems.　　In this way, a smooth surface can be formed on the surface.　　Limited. According to relevant materials, the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, the flow area in the pump body increases, which makes the flow increase after the impeller is cut.

　　In fact, the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes, as well as for advanced technologies, especially in the mining, chemical, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corroded　　Use a V megohmmeter to measure the insulation resistance between the electric pump motor and the phase to ground, and the value shall not be less than megohm. Otherwise, the stator winding of the motor shall be subject to monotonic treatment, and the monotonic treatment temperature shall not exceed ℃.　　Stability and reliability of seals between pump bodies.Potential development,　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.　　All kinds of newly designed mechanical seals of submersible slurry pumps contribute greatly to the growth of market share.

　　Second, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so IRecommendation and consultation,　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment will　　Some protection s are beyond the reach of manual operation.　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submergedChihuahua City ,　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　During adjustment,Chihuahua City Vertical multistage centrifugal pipeline pump, firstly loosen the support cover, then compress the nut,Chihuahua City Baigang deep well pump, and then loosen the bearing seat. After adjusting the screw tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation　　 The slurry pump mainly aims at conveying flow, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system certain