Whether I-section steel is ordinary or light, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane the moment of inertia of the two main axes of the section is quite different, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.The utility model has the advantages that the axial force of the roll is small, the axial movement is small, and the working slope is not required,Vienna New TownA335 P11 alloy pipe,Vienna New Town, Divided by weld -- straight welded pipe and spiral welded pipe.H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type,Vienna New TownPrice of 15CrMoG alloy pipe, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel,Vienna New TownHow much is a 25mm galvanized pipe, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable,Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.

Alloy steel pipe is a new type of seamless steel pipe connection pipeline. The selection of pipeline connection pipeline, whether it is fire water system software, water supply equipment, or pipeline, heat and national defense industrial pipeline system software of petrochemical pipeline system, alloy steel pipe stimulates important effects.The multi-al combination of reinforcement mesh welding machine and reinforcement mesh row welding machine based on PLC basic control. At present, the full-automatic mesh welding machine has the characteristics of simple operation, high control precision and easy to master the process of high-speed continuous welding. Judged as failing.Create brilliance,Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.a. In the forming process, the thick steel plate has uniform deformation, small internal stress and no scratch on the surface. The alloy pipe produced and processed has higher coordination ability in the scope of size, specification and model of diameter and wall thickness, especially in the production and manufacturing of steel structure design grade thick wall pipe, especially medium diameter small thick wall pipe, which has incomparable advantages of other processing technologies, and can meet a large number of customer regulations on the specification and model of alloy pipe.Alloy pipe can be divided into round steel pipe and special-shaped steel according to different cross-sectional area. Because the circular area is large on the premise of the same side length, a large amount of liquid can be transported with an annular tube. In addition, when the circular cross section bears the internal or external axial working pressure, the bearing force is more symmetrical. Therefore most seamless steel pipes are round steel pipes.

Small longitudinal crackInspection items,Mixed Scabs are distributed periodically, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal.Longitudinal welded pipe has the advantages of simple production process, high production efficiency, low cost and rapid development. The strength of spiral welded pipe is generally higher than that of straight welded pipe. It can produce welded pipe with larger pipe diameter with narrow blank, and welded pipe with different pipe diameter with blank of the same width. However, compared with the straight seam pipe with the same length, the weld length increases by ~ , and the production speed is low. Welded pipes with large or thick diameter are generally made of steel blank directly, while small welded pipes and thin-walled welded pipes only need to be welded directly through steel strip. Then after simple polishing, wire drawing is OK. Welded pipe is welded with strip steel, so it is not as high as seamless pipe in its original position. Welded pipe process: uncoiling of raw materials - leveling - end shearing and welding - looper - forming - Welding - removal of internal and external weld beads - pre correction - induction heat treatment - sizing and straightening - eddy current testing - cutting - hydraulic inspection - Pickling - Inspection (strict control) - Packaging - delivery.After isothermal quenching treatment the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment.Vienna New Town,I-beam: national standard * what is the wall thickness of I-beamWelded steel pipes need to be processed through various processes before application. The heat treatment of welded steel pipes is a very important link in the processing of welded steel pipes. Hot working is a metal hot working process in which metal materials are heated, insulated and cooled in a certain medium, and their metal properties are controlled by changing the metallographic structure on the surface or inside of the material. During the heating and cooling process of structural welded steel pipe workpiece, the temperature difference will be formed, which will lead to uneven volume expansion and contraction and produce stress, that is, thermal stress.I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.