[] Welding process of copper pipe Clean the end and seven ports of steel pipe with steel wool. Do not use abrasive cloth or abrasive paper to clean, because it will affect the clean interface and result in poor welding effect.Safe and reliable: copper pipe combines the advantages of metal pipe and non-metal pipe. It is harder than plastic pipes and has the high strength of ordinary metals (the strength of cold drawn copper pipes is equivalent to that of steel pipes with the same waess); It is also easier to bend than ordinary metals, has good toughness and high ductility, and has excellent anti vibration, anti impact and anti frost expansion properties.Yeliveska, we should properly keep the copper products we buy, extend the service life of copper and ensure its performance to avoid unnecessary losses.Glubokoye,Some steel mills in Liaoning are interested in purchasing pig iron, but the local resources are tight, and the iron mills quotations are on the high side resulting in a stalemate between supply and demand. The demand for cast iron and ductile iron in Jiangsu, Shandong,Yeliveska316L stainless steel pipe, Shanxi, Hebei, Henan and other regions is sluggish and the inventory pressure of iron mills is increasing. As the price of raw materials decreases, the quotation of iron mills continues to decline. At present the demand and cost support are weak, and there is no positive boost. The short-term pig iron market is weak and difficult to change.In the first ten days of May, the overall order receiving quantity of Tianjin Hebei Henan Plate Plant was not ideal. According to the monitoring data, the overall order intake of medium and heavy plate mills in Tianjin Hebei Henan region in the first ten days of May remained stable and weak. Due to the weak market shock, the overall order intake of the spot steel market was relatively weak. The total quantity of orders received in the first ten days of May is only about tons, while at the end of April, the total quantity of post settlement agreements of main steel plants can exceed tons.Remove the flame. If the filler metal does not melt, continue to heat the joint and try again. The melted filler metal is sucked into the casing port according to the capillary effect until a complete filler metal ring appears on the casing port. Remove the flame Pay special attention not to let the flame directly contact the filler metal. It should be the heat at the joint that melts the filler metal. In order to clean the copper pipe, the welding flux must have a degree of corrosivity,Yeliveska316L stainless steel plate, and shall be cleaned after brazing. The so-called & quot; self-cleaning& quot; fluxes are generally not recommended because of their corrosivity.

Some steel mills in Liaoning are interested in purchasing pig iron, but the local resources are tight, and the iron mills quotations are on the high side, resulting in a stalemate between supply and demand. The demand for cast iron and ductile iron in Jiangsu, Shandong, Shanxi, Hebei, Henan and other regions is sluggish, and the inventory pressure of iron mills is increasing. As the price of raw materials decreases, the quotation of iron mills continues to decline. At present, the demand and cost support are weak, and there is no positive boost. The short-term pig iron market is weak and difficult to change.Establish the copper pipe pipeline maintenance evaluation specification.In August, the price of domestic medium and heavy plates fell sharply. As of August , the price center of ordinary carbon boards in leading cities had dropped to , down yuan/ton from the end of July. At the beginning of the month, affected by the macro bad news, and the recent poor performance of fundamentals, the market mentality turned to pessimism, and some traders shipped at low prices. The market inventory rose, the inventory pressure was high, the stock shortage phenomenon disappeared, and the market transaction atmosphere was cold, the demand performance continued to decline, and the spot price fell under pressure.Create brilliance,Red copper inventory in key areas has risen continuously, but the total pressure is not big. From the current overall inventory situation of the main distribution centers Wu an, Jiangyin and Lecong, and the pressure on the market is relatively small. In Wu an market, as of May , the total inventory of medium and thick plates in Wu an was close to tons, increasing by tons on a weekly basis. In late April, it reached tons lower in the year, down tons from the high level after the Spring Festival, and rose for three consecutive weeks. In terms of the ovquantity, stability and performance and can save maintenance.Generally, oxygen aylene is used as the gas source and LPG welding tool is used for heating. The torch of the welding tool shall face the joint and then continuously heat the whole joint. This will avoid excessive local heating.

Remove the flame. If the filler metal does not melt, continue to heat the joint and try again. The melted filler metal is sucked into the casing port according to the capillary effect until a complete filler metal ring appears on the casing port. Remove the flame Pay special attention not to let the flame directly contact the filler metal. It should be the heat at the joint that melts the filler metal. In order to clean the copper pipe,YeliveskaCopper plate, the welding flux must have a degree of corrosivity and shall be cleaned after brazing. The so-called & quot; self-cleaning& quot; fluxes are generally not recommended because of their corrosivity.Process inspection,The hard copper tube is not artificially treated after being drawn or extruded, so that it can be naturally formed. At this time, the organizational form in the copper tube is full. This kind of copper tube is more likely to crack and is not suitable for bending. Therefore, the hard copper tube is generally straight.If the copper tube is blocked during use, it is also very important to dredge it in time.If the corrosion on the copper surface is found to be slight, it can be erased with linen copper wire, but it is not recommended to apply oil for preservation.Yeliveska,Because of the characteristics of copper itself, it is very easy to rust and corrode in places with high ambient humihumidity. If we often use it, the problem will be smaller, but if it is placed for a long time, the copper will be damaged. Many people do not know how to treat the copper surface? Now let the staff answer for you.When placing, they should be stored separately according to the different components, and should not be mixed together. The copper surface may have electrolytes, so it will react, especially with other materials such as rubber, which has a large impact.Five of the five major application fields of copper plate, copper bar and copper tube: copper is used in medicine. In the s, Chinese medical inventors Liu Tongqing and Liu Tongle found that copper has extremely strong s, and successfully developed the corresponding & quot; Cancer Suppressing & quot;