Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　The fruit is also bad; When the axial flow pump is used, its water output is relatively large, but the head is not too high, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from oneSanta Catalina pinura,　　Structural features of horizontal slurry pump: The ah, HH and L-type slurry pumps at the pump head are of double pump shell structure, that is, the pump body and cover are equipped with replaceable wear-resistant metal lining, and the flow passage components such as impeller sheath and guard plate are made of high chromium wear-resistant metal. The pump body and cover are made of grey cast iron according to the working pressure　　In fact, the impeller clearance of submersible slurry pump is not adjustable for all types of pump, but it is adjustable. During normal operation, the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation.Dzerzhinsk,　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choice　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water the slurry pump and submerged slurry circulating pump need to be placed above the water surface,Santa Catalina pinuraTwo stage slurry pump, and different pump models have different performance and application fields. Therefore, although the pump has a wide range of applications, if its model is not correctly and reasonably selected, its application effect will be great

　　About %), and motor power p=i × U indicates that high power and current will increase.　　Try to select the pump with appropriate lift.　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.Create brilliance,　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.　　The whole packing body, including the packing gland,Santa Catalina pinuraSelf priming slurry pump wholesale, packing ring and packing, shaft sleeve balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vane　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment

　　 First of all, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps mayOK or not?,　　When using the submersible slurry pump, no dilution of pulp, good shaft seal effect. It can be used when the slurry is not allowed to be diluted.　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is,Santa Catalina pinuraIrrigation deep well pump, in the traditional slurry pumpSanta Catalina pinura,　　.　　If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming.　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressure