The type selection planning of submersible slurry pump has a great impact on its service life and operation stability. A scientific and reasonable type selection plan will affect whether the slurry pump can achieve efficient operation. The operating power of the slurry pump is very high and the loss is small. Service life of flow passage parts of pump　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.Greensboro,GreensboroScrew deep well pump,　　It can be divided into single slurry suction pump and double slurry suction pump; The second is that the slurry pumps can be classified according to the pump shaft and horizontal position of the slurry pump: horizontal slurry pump and vertical slurry pump. The horizontal slurry pumps of Panshi pump are mostly ah, HH and ZJ　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.Cooperation,　　A large amount of lubricating oil is stored.　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. as

　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump　　 Before using the pump, carefully check whether the cable is damaged, and whether the pump is deformed or damaged during transportation, storage and installation.　　Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re usingScheme customization,　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump,GreensboroCirculating hot water pipeline pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise the motor will fall into the water　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, and the middle section including the guide vane; in addition,GreensboroPipeline pump body, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurry

　　In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium,　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　 sedimentation tanks, hydropower stations reservoirs, rivers, power plants, open caissons, mines and fish ponds.　　Limited. According to relevant materials the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, the flow area in the pump body increases, which makes the flow increase after the impeller is cut.Greensboro,　　With water, you can start working.　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.