In this way, when the equipment is used again, the solvent in the pump is often less, and the power consumption is also less, and the efficiency of the pump in use is often improved, and the fact is　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.New Orleans, the submersible pump cannot be started. The reason can only be understood from the submersible pump. Submersible pump bearings may be damaged and the pump may be blocked. The impeller is full of groceries. Submersible pumps shall not be used for sundries, such as those wrapped around the pump shaft　　It is also necessary to clean the ventilation duct to avoid blockage.Grand Gorica,　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation,New OrleansQJ submersible pump, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, so

　　Some impurities will entangle the impeller, so generally, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.　　Several common specifications and models.　　After the submersible slurry pump leaves the factory, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.High value, and transmits energy to the slurry medium to generate a certain flow rate the motor shaft drives the water pump impeller to rotate, drive the solid flow, and realize the transportation of slurry.　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can

　　 selection of raw materials for flow passage parts: the raw materials for flow passage parts of the pump can be selected according to the particle composition, particle size shape, hardness, concentration, acid, alkali and other characteristics of the transported materials.Affordable price,　　 strip the outer layer of the cable to expose the copper wire for to mm,New OrleansSubmersible non clogging slurry pump, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.　　Static water level refers to the water level before the pump is started.　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular, some equipment is frequently used at ordinary times, so it will be blocked after being used for a period of timeNew Orleans,　　Causes: there is air or gas accumulation in the water inlet pipe of the pump,New OrleansVertical slurry pump, or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced the cost has been reduced, and the income has been increased.　　Whether the pump is evacuated or overflowed, etc., and handle it at any time.