TarangaIrrigation deep well pump,

　　 First remove the pump from the engine.　　Balance of.Taranga,　　Dynamic water level: after the pump operates normally, the water inflow in the pool and the pumping capacity of the deep well pump reach an equilibrium point, and the water level at this time is called dynamic water level.　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, the motor will fall into the waterIlobu,　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating so that the product can operate safely for a long time under adverse working conditions.　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energy

　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, so it is also a reminder that we are using it too　　 Change the oil: if the oil contains water, drain it change the oil, seal the gasket, and then tighten the screw plug.　　Be sure to choose a pump that is more suitable for use.Sincere service,　　The development of submersible slurry pump is to adapt to increasingly complex working conditions,TarangaScrew deep well pump, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pump　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter, so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent, and the degree of blade overlap will decrease with the addition of specific speed　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can

　　Submersible slurry pumps are mainly used in mining, coal, environmental protection, in the field of chemical industry, corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump bladeFair price,　　When using the sand pump,TarangaCentrifugal slurry pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid　　For the pipeline pump in the workshop, it is necessary to consider whether the pipeline pump is worn to a certain extent due to inadequate maintenance, but the performance of the pipeline pump is degraded. In case of abnormal water absorption during installation, check the motor during installation, and check the motor wiring and speed,　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for useTaranga,　　Occurrence of personal injury accident. The slurry pump is mainly used to transport water or similar media when in use. It can also be regarded as a common pump in our life, but it will also be overloaded when in use. Let&#;s have a look today　　Sex is different. Although the submersible slurry pump is widely used, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump, dredging pump, desilting pump, etc. are all in the application scope of the slurry pump　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation which can be brought wherever it is needed, because it does not need too many auxiliary facilities.