Solution treatment. The main purpose of water quenching after heating the steel to ~ ℃ is to dissolve the carbide in austenite and keep this state to room temperature, solid solution treatment is usually used to dissolve CrC in austenite and then cool rapidly. Air cooling can be adopted for parts in order to prevent intergranular corrosion, and water cooling is generally adopted.The operators are mainly plumbers and argon arc welders, with the cooperation of other types of work, and the argon arc welder shall have the certificate issued by relevant departments.Lac,　　— High strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It belongs to hard stainless steel. A common application example is & ldquo; Shaving blade & rdquo;. There are three common models: C and f (easy to process).The corrosion resistance is the same, and the strength is better because the carbon content is relatively high.Frashatz,Formula for hydraulic test pressure of stainless steel welded pipe for weight calculation fluid (gbt-): where: P - test pressure, MPa; R - stress, taking yield point of %, MPa; s - nominal wall thickness of steel pipe, mm; D - Nominal outer diameter of steel pipe, mm.Standard classification - classification: national standard GB industry standard Yb local standard enterprise standard qcb- classification: product standard packaging standard basic standard - standard level (divided into three levels): y level: international advanced level I level: international general level H level: domestic advanced level - national standard: stainless steel bar (level I) gb- stainless welding disc Park (level H)Deformation strengthening of austenitic stainless steel stainless steel has good cold deformation performance. It can be cold drawn into very thin steel wire and cold rolled into very thin steel strip or steel pipe. After a large amount of deformation the strength of the steel is greatly improved, especially when rolling in the subzero temperature zone. The tensile strength can reach more than MPa. This is because in addition to the cold hardening effect, there are also superimposed Deformation induced M transition.

AUSTENITIC FERRITIC duplex stainless steel on the basis of austenitic stainless steel, appropriately increase Cr content and reduce Ni content, and cooperate with remelting treatment. High prices, various specifications of stainless steel plates, stainless steel coils, stainless steel belts and stainless steel tubes are supplied in time and cost-effective. It has become the preferred brand for many wire products. Welcome to buy! Stainless steel with duplex structure of austenite and ferrite (including ~ % & Delta; - ferrite) can be obtained. Typical steel grades include crniti,LacStainless steel rectangular tube, CrNiTi, ocrnimoti, etc. Duplex stainless steel has good weldability, no heat treatment is required after welding, and its tendency of intergranular corrosion and stress corrosion is also small. However, due to the high Cr content, it is easy to form & sigma; Pay attention when using.The application of stainless steel pipe in the automobile industry is developing rapidly. In recent ten years, stainless steel pipe materials have been widely used in public transportation tools such as buses,Lac305 stainless steel square tube, subways, household cars and so on!At present, stainless steel backing is divided into two processes: back argon filling and non argon filling. Back argon filling protection can be divided into solid wire + TIG process and solid wire + TIG + water-soluble paper process; The back non argon filling protection is also divided into flux cored wire backing welding and welding rod (flux coated wire) backing TIG welding.Application process,Model & mdash; It has better temperature resistance.Model & mdash; The corrosion resistance is the same, and the strength is better because the carbon content is relatively high.The petrochemical industry, including the chemical fertilizer industry, has a great demand for stainless steel pipes. Stainless steel pipes are mainly used in this industry, including, , etc., with an outer diameter of about ￠ - ￠ and a wall thickness of about mm-mm (generally medium and low pressure transmission pipes with a specification of more than & phi; mm). The specific application fields are: furnace pipes, material transmission pipes, heat exchanger pipes etc.

When hoisting stainless steel pipes, public slings, such as hoisting belt and public collet number, shall be used. It is strictly prohibited to use steel wire rope to avoid scratching the surface; and when hoisting and placing, it shall prevent scratching caused by impact and collision. If there are surface scratches, electric arc traces and surface purification in the process of transportation, storage and processing, polished with an angle grinder, and then polished Polishing with optical sheet or metallographic sandpaper.project,Model & mdash; Except that the risk of weld corrosion of the material is reduced due to the addition of titanium, other properties are similar. Stainless steel decorative pipe, series stainless steel pipe & mdash; Ferritic and martensitic stainless steel model & mdash; Good heat resistance, weak corrosion resistance, % Cr, % Ni.In addition to stress corrosion resistance, professional stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe have stable, safe and reliable performance and can be maintenance free. The technical level has reached the domestic level and the advanced level of similar international products. Other local corrosion resistance properties are better than ferritic stainless steel.The bright nickel layer on the stainless steel pipe is a silver white metal with slight yellow light. Its hardness is higher than that of copper,Lac316L stainless seamless steel pipe, zinc, tin, cadmium, gold and silver, but lower than that of chromium and rhodium. Bright nickel has high chemical stability in air and good stability to alkali. Using Brightener on stainless steel pipe, bright nickel can be directly plated without polishing, so as to improve the hardness, wear resistance and leveling of the surface, make the appearance of stainless steel pipe consistent with other nickel plated parts, and avoid the corrosion of potential difference between stainless steel pipe and other bright nickel. After using bright nickel solution for a period of time due to the of brightenerLac,Austenitic stainless steel austenitic stainless steel is developed to overcome the lack of corrosion resistance and brittleness of martensitic stainless steel. The basic composition is crl% and Ni%, which is referred to as - steel for short. Its characteristic is that the carbon content is less than .%, and the single-phase austenite structure is obtained by the combination of Cr and Ni. Series & mdash; Martensitic precipitation hardening stainless steel.Proper heat treatment process can prevent intergranular corrosion and obtain excellent corrosion resistance.