I-beam is widely usedI-beam is a long strip steel with groove section, which belongs to carbon structural steel for construction and machinery. It is a section steel with complex section, and its section shape is groove shape. China&#;s imports of I-beams are greater than its exports. The main producing areas are Tangshan Iron and steel, Baotou Iron and steel, Shangang, huangte, Maanshan Iron and steel, Xuanhua Iron and steel, Japan iron and steel, etc.St. Johns, Spiral seam submerged arc welded steel pipe for general low-pressure fluid transportation (SY / t- is a submerged arc welded steel pipe for general low-pressure fluid transportation such as water, gas, air and steam, which is made of hot-rolled steel strip coil as pipe blank, often warm spiral forming and double-sided active submerged arc welding or single-sided welding.With the development of steel structure buildings, only I-beam is not enough, that is, which is easy to lose stability for load-bearing columns.Tanout, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure. The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.According to the national standard of hot rolled H-section steel in China (GB / t-, H-section steel is divided into narrow flange, wide flange and steel pile, whose codes are Hz, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W, IX and iy are not as good as H-section steel under the premise of equal weight.

Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center,St. JohnsQuotation of welded pipe manufacturer, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.Check whether the manufacturer&#;s qualification, business license, organization code certificate, tax registration certificate, production and operation license and other qualification materials are complete. Look at the case, choosing a service provider with a self built logistics fleet can reduce the transportation cost, and more importantly, ensure the timeliness of delivery. After sales service whether there is a sound and reliable after-sales service guarantee system, and timely solve quality problems in arrival acceptance and subsequent use. Check whether the quality assurance materials such as product quality certificate, material specification and warranty are complete. Check the appearance of the welded pipe, the surface is smooth and flat, the weld is dense, without burr, oil stain, corrosion, extrusion deformation and flat cross section. Use a micrometer to check whether the outer diameter and wall thickness of the welded pipe meet the requirements, and the standard wall thickness deviation shall not exceed % - %. NDT shall be carried out for welded pipe with flaw detector. Conduct bending tensile strength test according to the requirements, bend the welded pipe for degrees, and there is no crack at the bend.→ I-beam can be processed into T-beam, and honeycomb beam can be combined to form various section forms, which greatly meets the needs of engineering design and manufacturing.Potential development,Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.b. The professional two-sided arc welding processing technology can complete the electric welding at a good position, welding deviation and incomplete penetration, and it is very easy to manipulate the welding quality. Judged as failing.

Alloy pipe is a kind of seamless steel pipe. Alloy pipe is divided into structural seamless pipe and high-pressure heat-resistant alloy pipe. It is mainly different from the production standard and industry of alloy pipe. Annealing and tempering of alloy pipe changes its mechanical properties. Meet the required processing conditions. Its performance is higher than that of ordinary seamless steel pipe, its utilization value is higher, the chemical composition of alloy pipe contains more Cr, and its performance of high temperature resistance, low temperature resistance and corrosion resistance. Ordinary carbon seamless tubes do not contain alloy components or have few alloy components. Alloy tubes are widely used in petroleum,St. JohnsHow much is the wholesale price of welded pipe, aerospace, chemical industry, electric power,St. JohnsHow much is 150 welded pipe per meter, boiler and other industries because the mechanical properties of alloy tubes change and are easy to adjust.How much does it cost?,Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Idler pipe: it is used for electric welding steel pipe of idler of belt conveyor. It is generally made of Q, QA B steel and steel, with a diameter of -mm. There are certain requirements for pipe tortuosity end face straightness with the center line and ovality. Generally,Under the action of thermal stress water pressure and flattening tests are carried out.Requirements of alloy tubes for low and medium pressure boilersSt. Johns, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.Dehydrogenation solution: the alloy pipe shall be dehydrogenated after passivation treatment to avoid alkali embrittlementXhy- series high hardness alloy I-beam; Undertake drawings and process wear-resistant pipes（ Φ ≥mm）； Undertake the processing and production of vulnerable parts of cement machinery; Welding technology consultation and service; The wear-resistant layer of alloy wear-resistant plate of high chromium heap welding flux cored wire series is mainly high chromium, as well as manganese, molybdenum, niobium