Model & mdash; High strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It belongs to hard stainless steel. A common application example is & ldquo; Shaving blade & rdquo;. There are three common models: C and f (easy to process).The corrosion resistance is the same, and the strength is better because the carbon content is relatively high.Guane,Seamless steel pipe): round billet & rarr; Heating → Perforation & rarr; Three roll cross rolling, continuous rolling or → Off pipe & rarr; Sizing (or reducing) → Cooling → Straightening & rarr; Hydrostatic test (or flaw detection) → Mark & rarr; The raw material for warehousing and rolling seamless pipe is round pipe blank. The round pipe blank shall be cut and processed by cutting machine, it should be pierced through the pressure piercer. Generally, the more common piercer is the cone roll piercer. This piercer has high production efficiency and good product quality. It is specialized in stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation protection, long service life, large perforation diameter expansion, and can wear a variety of steel grades. After perforation, the round tube blank is successively rolled by three roll cross rolling, continuous rolling or rolling. Take off the pipe after sizing. The conical drill bit of the sizing machine rotates into the steel embryo at high speed to form a steel pipe. The inner diameter of the steel pipe is determined by the outer diameter length of the sizing machine bit. After sizing, the steel pipe enters the cooling tower for water spray cooling. After cooling, the steel pipe will be straightened. After straightening the steel pipe is sent to the metal flaw detector (or hydrostatic test) for internal flaw detection. If there are cracks, they will be detected. Steel pipes should be strictly selected manually after quality inspection. After the steel pipe is inspected the number, specification, production batch number, etc. shall be sprayed with paint. And hoisted into the warehouse by crane.Construction materials shall be prepared and delivered to the site according to the data scheme,Guane10cr17 stainless steel plate, and shall be supplied according to the scheme.Vohibinany,The numbering rules adopt element symbols; Pinyin, open hearth steel: p; Boiling steel: F; Killed steel: B; Class a steel: a; T: special GCr: ball.In order to ensure the appearance quality of continuous casting slab, select appropriate maintenance slag; During continuous casting, the vibration marks formed on the surface of continuous casting slab due to the vibration of mold shall be; Electromagnetic stirring must be used in continuous casting of ferritic stainless steel pipe fittings. Series & mdash; Martensitic precipitation hardening stainless steel.

Stainless steel pipe is durable and has been recognized by the engineering community, so as to facilitate further development. In particular, the price of stainless steel pipe is not high, so the supporting connection the reliability and price of pipe fittings are the main factors determining its development. Domestic developers have independently developed connection technology and pipe fittings in Sichuan, Guangdong, Zhejiang,GuaneStainless steel medical tube, Jiangsu and other places, which is a promising pipe. The Ministry of construction and relevant departments also attach great importance to this new type of pipe. According to China technology market management promotion center and gksz [] No. document on Application & ldquo; High diameter to wall ratio and high precision stainless steel medium and high pressure water supply pipes and supporting fittings and special technology & rdquo; It is learned from the notice that the application of stainless steel pipe technology and product is of great significance to improve the grade of modern buildings in China and improve and ensure the water quality of water supply.The resistance, linear coefficient, thermal conductivity, quality, hot melt and magnetism of stainless steel pipe will change greatly at low temperature. Resistance, line coefficient decreases at low temperature; The thermal conductivity and mass heat capacity decrease sharply at low temperature; Young's modulus (longitudinal modulus) increases when the temperature decreases. Because the austenitic series stainless steel pipe has MS point (martensite start temperature or martensite formation temperature) at low temperature (subzreo temperature), martensite can be formed when it is kept below MS point. The formation of martensite at low temperature makes the representative steel sus (Cr-Ni) of austenitic stainless steel non-magnetic at room temperature and magnetic at low temperature.The operators are mainly plumbers and argon arc welders, with the cooperation of other types of work, and the argon arc welder shall have the certificate issued by relevant departments.equipment maintenance ,Production process of stainless steel welded pipe: raw material - strip - welded pipe - end repair - polishing - Inspection (spray printing) - Packaging - shipment (warehousing) (decorative welded pipe).Various welding methods of combined welding stainless steel welded pipe have their own advantages and disadvantages. Combined welding methods include argon arc welding plus plasma welding, high-frequency welding plus plasma weldingModel & mdash; It has better temperature resistance.

Model & mdash; High strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It belongs to hard stainless steel. A common application example is & ldquo; Shaving blade & rdquo;. There are three common models: C and f (easy to process).Which one is better,That is stainless steel. The GB brand is CrNi. & mdash; it has better temperature resistance than it.[hot rolled strip / sheet] has the advantages of low hardness, it is widely used in the national economy. Because the steel pipe has a hollow section, it is suitable for gas and solid transmission pipelines; at the same time, compared with the round steel of the same weight, the steel pipe has large section coefficient and high flexural and torsional strength, so it has also become an important material in various machinery and building structures. Stainless steel is used Under the condition of equal weight the structure and components formed by pipe have a larger section modulus than solid parts. Therefore, stainless steel pipe itself is an economic section steel that saves metal. It is an important part of steel, especially in oil drilling, production and metallurgyGuane,Solution treatment. The main purpose of water quenching after heating the steel to ~ ℃ is to dissolve the carbide in austenite and keep this state to room temperature, so that the corrosion resistance of the steel will be greatly improved. As mentioned above, in order to prevent intergranular corrosion, solid solution treatment is usually used to dissolve CrC in austenite and then cool rapidly. Air cooling can be adopted for parts, and water cooling is generally adopted.In the building water supply pipe system, due to the end of the glorious history of galvanized steel pipe, various new plastic pipes and composite pipes have developed rapidly, but various pipes still have some deficiencies in varying degrees, which are far from fully meeting the needs of water supply pipe system and the national requirements for drinking water and related water quality. Therefore, relevant experts: building water supply pipes will eventually return to the era of metal pipes. According to foreign application experience stainless steel pipe is recognized as one of the pipes with good comprehensive performance in metal pipe.When the stainless steel fixed port is welded, it will be difficult to ventilate on both sides of the weld. At this time, how to ensure the argon filling protection on the inner side of the weld has become a difficult problem. For a long time, facing the national high price, the reasonable price and perfect service of all kinds of stainless steel plates, stainless steel coils, stainless steel belts and stainless steel pipes have been recognized by the majority of customers. In the actual construction on site, we use two welding joints The above problems were successfully solved by plugging with water-soluble paper on the side, ventilation from the weld center and sealing with adhesive tape on the outside (see Table ).