Seventh, sound insulation and noise reduction.In addition pay attention to whether there are sawdust and stratification on the cutting surface of the plate and whether there are sawdust and stratification on the cutting surface of the solid wood floor.Santa Clara,The structure of solid wood multilayer composite floor is divided into solid wood control panel,Santa ClaraHow much is the price of floor leather? One square meter, the formaldehyde released will be less than that of reinforced composite floor. Domestic cheap decorative paper is usually used. The pattern of this decorative paper is fuzzy. The biggest defect is that it is generally not UV resistant and will fade after sunlight.This is why some consumers reflect the discoloration of the places near the balcony and windows three or four months after the floor is installed. The base material is poor, medium and low density board or particleboard is used, the quality index is unstable, and the formaldehyde seriously exceeds the standard.Nyaungdon,Moisture content is one of the most important factors affecting the reliability of solid wood composite flooring. When purchasing solid wood composite flooring, so as to avoid early dry crack and aging of the floor surface.Close the window when it rains so as not to wet the floor.Also pay attention to indoor ventilation,Santa ClaraHow to clean composite wood floor, emit indoor moisture and maintain normal indoor temperature, which is also conducive to the service life of the floor.SPC floor is composed of thickened wear-resistant layer,Santa ClaraSPC flooring factory, UV layer, color film texture layer and substrate layer.Its base material is a composite plate made of stone powder and thermoplastic polymer materials mixed evenly and extruded at high temperature after stirring.At the same time, it has the properties and characteristics of wood and plastic to ensure the strength and toughness of the floor.Let&#;s take a look at the advantages of SPC floor.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.Where is good,The surface layer of SPC floor has been solved by pur Crystal Shield, with good thermal insulation performance. It will not be cold even if barefoot steps on it. It is very comfortable. Coupled with the rebound technical layer, it has good flexibility.Even if you keep bending degrees, you don&#;t have to worry about falling pain. It is especially suitable for homes with elderly and children.SPC floor will be very astringent in case of water, that is, the sliding friction will increase, and the ground anti-skid performance will be very good.It also has high wear resistance.Even if the floor is rubbed back and forth with a steel wire brush, there will be no scratches, and the service life is more than years.Moreover, SPC floor is very light, with a net weight of only -kg per square meter, which is % of the raw materials of general floor. It can reasonably save the height width ratio of indoor space and reduce the bearing capacity of the floor.The SPC floor does not swell and deform, and does not need to be maintained in the middle and later stages. There is a sound insulation and noise reduction layer at the bottom, and the actual effect of sound insulation and noise reduction is also very good.There are many kinds of floors used in interior decoration. Community owners who have experience in interior decoration should know that different kinds of floors have different home decoration effects. Which kind of floor is better?Let&#;s take a look at the types of solid wood composite flooring.Secondly, the main standard of floor environmental protection is formaldehyde emission.In terms of the limitation of formaldehyde emission standards, the environmental protection of the flooring industry has experienced three technological revolutions: E, E and FCF.At an earlier stage, the formaldehyde emission standard of wood-based panel is E level (formaldehyde emission ≤ mg / g), and its formaldehyde emission limit is very loose. Even for products meeting this standard, the formaldehyde content may exceed more than three times that of E level wood-based panel, seriously endangering human health, so it must not be used for home decoration.Therefore, there was the first environmental protection revolution. In this environmental protection revolution, the flooring industry implemented the E level environmental protection standard that is, the formaldehyde emission is ≤ ? / L. although it basically does not pose a threat to the human body, there are still a lot of free formaldehyde left in the floor.The flooring industry has started the second environmental protection revolution and launched E environmental protection standard, which has reduced the formaldehyde emission of the floor to . ? / L.The best way to identify whether the floor is environmentally friendly is to pry the floor from the lock with a screwdriver and hammer, so that the floor substrate is exposed in a large area, and then smell it with your nose. A good floor should have a wood smell, but a bad one has a strong pungent smell!

Use place of SPC floor: because of its thin thickness, many colors, complete styles and low-carbon environmental protection performance, it can be widely used in kindergartens, hospitals offices, office buildings, shopping malls homes, KTV and other public places. Ecological and environmental protection.Workshop cost, Silencing, comfortable and elastic walking feet, not easy to be injured when fallingInspection results:Defects: some indoor formaldehyde is restrained, the quality of the sales market is uneven, and most plates are shoddy.Santa Clara, Main performance.When selecting accessories, we should also consider the cost. We should select thin or narrow right angles and strips, which virtually limits the shrinkage space and causes unnecessary losses.First